InfiniCon Systems VAP016 User Manual download pdf (Page 2)

Installation

Vacuum Connection

Skilled personnel

The vacuum connection may only be established

by persons who have suitable technical training

and the necessary experience or who have been

instructed by the end-user of the product.

DANGER

Caution: overpressure in the vacuum system

>1 bar

Injury caused by released parts and harm

caused by escaping process gases can result if

clamps are opened while the vacuum system is

pressurized.

Do not open any clamps while the vacuum

system is pressurized. Use the type clamps

which are suited to overpressure.

Caution

Caution: dirt sensitive area

Touching the product or parts thereof with one's

bare hands increases the desorption rate.

Always wear clean, lint-free gloves and use

clean tools when working in this area.

Caution

Caution: vacuum component

Dirt and damages impair the function of the

vacuum component.

When handling vacuum components, take

appropriate measures to ensure cleanliness and

prevent damages.

Caution

Keep the protective lids and put them in place

again when removing the product from the

vacuum system.

Remove the protective lids and install the valve to the

vacuum system by means of the small flange fittings.

Any installation angle and flow direction may be chosen.

Seal with

centering ring

Clamp

ISO-KF

connection flange

Protective lid

Compressed Air Connection

Skilled personnel

The compressed air connection may only be

established by persons who have suitable tech-

nical training and the necessary experience or

who have been instructed by the end-user of the

product.

Caution

Specifications for the plastic tube:

· ø4 mm, ø6 mm or ø¼“

· bursting pressure ³ 10 bar overpressure

(1 MPa)

· material: PA soft or PU.

Caution

The compressed air must meet the following

specifications:

· free of particles >5 µm

· DN 16 and DN 25: 3 … 5 bar overpressure

DN 40: 3 … 6 bar overpressure

· dry, free of oil or containing oil

(keep using the same quality).

If compressed air containing oil is used, dispose

of the exhaust compressed air outlet in

accordance with the relevant regulations.

Caution

To ensure leak tightness of the instant push-in

fitting

· cut the plastic tube square

· make sure the outside of the plastic tube is

not damaged.

Caution

Caution: plastic thread

The plastic thread is damaged by tilting or

overturning the instant push-in fitting.

· use the enclosed instant push-in fitting (with

extra-long thread) only.

· screw in the instant push-in fitting without

tilting it and without exceeding the tightening

torque of 0.5 Nm.

Compressed Air Inlet

Caution

Contrary to the illustration below, the compres-

sed air inlets and outlets of the following angle

valves are reversed in position:

Vacuum connection DN 40 ISO-KF and serial

number (F-No) from

· 101 for valve with aluminum housing

· 118 for valve with stainless steel housing

If you wish to connect a ø6 mm, or ø¼“ plastic tube,

exchange the instant push-in fitting.

Tightening torque 0.5 Nm

Compressed air

inlet

Compressed air

outlet

Insert the tube into the instant push-in fitting until the

mechanical stop is reached. Check that it is correctly

mounted by slightly pulling.

Compressed air

inlet

Compressed air

outlet

Plastic tube

Compressed Air Outlet

Caution

Contrary to the illustration below, the compres-

sed air inlets and outlets of the following angle

valves are reversed in position:

Vacuum connection DN 40 ISO-KF and serial

number (F-No) from

· 101 for valve with aluminum housing

· 118 for valve with stainless steel housing

Screw in the enclosed instant push-in fitting for exhausting

the compressed air if necessary. Push the tube into the

instant push-in fitting until the mechanical stop is reached.

Check that it is correctly mounted by slightly pulling.

Tightening

torque 0.5 Nm

Compressed air outlet

Compressed air inlet

Electrical Connection

Skilled personnel

The electrical connection, in accordance with the

VDE 0100 guidelines, may be made only by a

licensed electrician, qualified as per VDE 0105.

The line cables shall be isolated from the line

supply during all electrical work.

WARNING

Caution: mains voltage

The pilot valve can get destroyed if a wrong

mains voltage is applied.

The local mains power rating must correspond

with the nominal voltage of the pilot valve (see

product nameplate). If they do not correspond,

exchange the pilot valve (® Furter information).

Caution

The cable must meet the following specifications:

· flexible

· conductor cross-section £0.75 mm

· cable diameter £10 mm

· 6-pole without protective conductor or

7-pole with protective conductor.

Preparing the connector

 Slide the screw fitting, connector housing, and strain

relief on the cable.

Screw fitting

Connector housing

Strain relief

Seal

Washer

Hex head screw

si ma60e1- b

(0210)

Original: German sima60d1-b (0210)

1 2 3 4

Comments to this Manuals

No comments

InfiniCon Systems VAP016 User Manual Page 2

Comments to this Manuals